Maximizing Enhanced ROI Through Technical Link Automation

An advantage to this setup is that it takes just seconds to move from lathe to milling operations. The disadvantage to the new toolpost (and there's constantly a disadvantage) is that it restricts the size of products which can be turned due to its large size; I included the modified compound rest # 1777 from LMS to assist accommodate this and eventually modified the cross slide to allow more range.
My carriage lock is based on Mike Walsh's style. This would make a beneficial second project although there is more filing, sanding, and polishing than turning. A taper accessory for the mini lathe; it works much better since adding struts to stiffen the mounting. Here is a 3C collet chuck to fit the 3MT taper in the minilathe headstock - the raw product for the chuck was a barbell bar.
The equipment is the chuck extractor, the "?" gizmo is a wrench to use more torque to the equipment. The chuck is revealed here in the lathe. The collets are another part of this project; this is a photo of the raw material, an acquired collet, and a partly finished pair. To slot the collets I purchased a slitting saw, then made an arbor to fit the collet chuck - here is a photo of the parts. Slitting is slow work with this setup however it gets the job done, witness the collet revealed. Sadly, this collet was not drilled accurately so it is ineffective due to excessive runout. Ball bearings were contributed to the mini-lathe controls, beginning with the cross slide followed by the substance (much simpler to do than the cross slide).

The cross feed and substance dials were transformed to complimentary spinning with friction lock simple to do, works well, changes the friction spring under the dial. My initial reason for getting a lathe was to make items related to my microscopic lense pastime however I got into adjusting lathe associated stuff.
His article recommends utilizing the cross feed to knurl but this puts substantial pressure on the cross feed lead screw and nut; using the carriage feed instead works well and puts less pressure on the device.

Why Invest in Automated SEO Solutions?
When is a tool height gauge not a tool height gauge?-- you get 2 for the price of one with this approach.
I copied Varmint Al's idea for a tailstock flag and meter. Used a piece of 1/2" Lucite for the flag, the magnet is the rotor from a VCR takeup motor with an aluminum bracket to mount the meter; simple, low-cost, effective. The DRO has even more streamlined drilling to depth. Made a plinth to replace the compound for most things besides threading and tapers.
Eventually I figured out that pulling back the compound so the tool point is over the cross slide (not cantilevered out to the headstock side) assists minimize chatter and the plinth I made doesn't enable this. This doesn't fit nicely within the title of my site so I do not know exactly how I'll work that out but after wrestling this 700 pound guy down the stairs and onto the table, the mill stays!
Streamlining Backlink Creation With Advanced Software
A Mini-Tinker cutter mill didn't work as I hoped for sharpening end mills so ultimately I purchased a cutter grinder (see below) which didn't exercise either ... Tool holders to fit my Stage II toolpost were on my order of business for a while; the brand-new mill made numerous things possible.
I get a better finish on steel with this toolholder than with routine toolholders and bits so I now use this for most turning and facing. I made Will Hamlyn's split nut mod to reduce backlash in the cross slide. This didn't work as well as I hoped so I split the old nut lengthwise rather but it cracked when squeezed so I use it with 5 thou backlash.
; this is more capable than either of my earlier approaches to end mill honing. This is much more useful than expected, well worth doing.
In making the leadscrew for the Brooks-Stent I needed a sharp threading bit so I constructed the honing jig from "Screwcutting in the Lathe" by Martin Cleeve. This jig makes the task fast and easy. A little exploring with this jig showed that it can be utilized to sharpen numerous lathe (and shaper) bits besides threading bits and the results are clearly much better than my hand sharpening efforts.

I constructed a Geo. I do a reasonable quantity of threading so I've developed a regular for it which this tool streamlines.
The Strategic Benefits of Professional Link Automation
Combined with the pulling back toolholder this accelerate threading substantially. Built a graver rest for the minilathe; a collet chuck or comparable is needed to utilize it safely. Included a pet clutch type carriage auto-stop to more enhance threading; this supplies automated thread pickup on both royal and metric threads plus it eliminates need for the thread chasing dial.
As a non-woodworker, the case is an on-going battle although the short-lived case is adequate for now.
ready to restore .ser fileMade a tapping guide from a surplus sign stand. Ended up an ER-32 collet chuck for the Rockwell. ER-32 Collets can now be used on the 7x12, Rockwell 10" and the mill-drill. Little tools get allured accidentally (magically) in my shop so I made a demagnetizer from scrap plus small neodynium magnets.
Developed a cut knurler as an experiment. Seems to work well, much easier on the device than the pressure knurler but seems a little fussier to establish. Included information on making counterbores from drill rod. Copied Dan Gelbart's Laser Center Finder idea for use with the mill or drill press.
Building Professional Link Engines for 2026 and Beyond
, both of which are likely of interest primarily to clockmakers.